Aeg-Electrolux 21602G-M Uživatelský manuál

21602 GInstruction Booklet Gas HobGB

10OVERALL DIMENSIONS Width: 580 mmDepth: 500 mmCUT OUT DIMENSIONS Width: 550 mmDepth: 470 mmSUPPLY CONNECTIONS Gas:R 1/2 inch (1/2 inch male) Rear rig

11BURNER RAPID SEMI-RAPID AUXILIARY(large) (medium) (small)POSITION MAX MIN MAX MIN MAX MIN NOMINAL THERMAL POWER kW 3.0 0.75 2.0

12Important safety requirementsThis hob must be installed in accordance with the Gas Safety (Installation and Use)Regulations (Current Edition) and th

13InstallationIMPORTANTThis hob must be installed by qualified personnel to the relevant British Standards.Any gas installation must be carried out by

14A) End of shaft with nutB) WasherC) ElbowFO 0814FO 0264On the end of the shaft, which includes the G 1/2" threaded elbow, adjustment is fixed s

15Building InBuilding over a cupboard or drawerIf the hob is to be installed above a cupboard or drawer it will be necessary to fit a heatresistant bo

16Building over a kitchen unit with doorProper arrangements must be taken indesigning the furniture unit, in order to avoidany contact with the bottom

17Fitting the hob to the worktopBefore fitting the hob into the cut out, asealing gasket supplied with the hob mustbe fitted to the edge of the cut ou

18Electrical connectionsAny electrical work required to install this hob should be carried out by a qualifiedelectrician or competent person, in accor

19Permanent ConnectionIn the case of a permanent connection, it is necessary that you install a double poleswitch between the hob and the electricity

2

20Fault FindingPreliminary Electrical Systems CheckSTARTIsolate applianceand carry out:A: Earth Continuitycheck. Has inlet fuse blown?Carry out:C: Pol

21A. EARTH CONTINUITY CHECKAppliance must be electrically disconnected - meter set on W (Ohms) x 1 scale andadjust zero if necessary.— Test leads from

22Check gas supply atburnerIgnition System / Gas IgnitionYESCheck plug top fuse andreplace if necessaryCheck polarity and earthcontinuity of supply po

23CommissioningWhen the hob has been fully installed it will be necessary to check the minimum flame setting.To do this, follow the procedure below.1)

24Conversion from Natural Gas to LPGIt is important to note that this model is designed for use with natural gas but can be converted for usewith buta

25Guarantee ConditionsStandard guarantee conditionsWe, AEG-Electrolux, undertake that if within 12 months of the date of the purchase this AEG-Electro

26Service and Spare PartsBefore calling out an engineer, please ensure you have read the details under the heading“Something not working”When you cont

27* calls to this number may be recorded for training purposes.Customer CareFor general enquiries concerning your Electrolux appliance, or for further

28

29

3Important Safety InformationYou MUST read these warnings carefully before installing or using the hob. If you needassistance, contact our Customer Ca

30

31

35678-5905 10/07 R.A Subject to change without notice

4 Ensure the control knobs are in the ‘OFF’ position when not in use. When using other electrical appliances, ensure the cable does not come into co

5ContentsImportant Safety Information... 3Description of the H

61. Hob Top2. Rapid Burner3. Semi-rapid Burners4. Auxiliary Burner5. Control knob for back right burner (semi-rapid)6. Control knob for back left burn

7Hob burners control knobs The symbols on the knobs mean that :  there is no gas supply there is maximum gas supply there is minimum gas supplyLighti

8Before any maintenance or cleaning can be carried out, you must DISCONNECT thehob from the electricity supply.The hob is best cleaned whilst it is st

9Something Not Working?If the hob is not working correctly, please carry out the following checks before contacting yourlocal AEG-Electrolux Service